Search | Statistics | User Listing | Member Roster | Coach DB Forums | Albums

Home -> FMC Owner's Forum -> Albums -> View Album

You are logged in as a guest. ( logon | register )

#846 - Cummins Swap

Author: andy1canada (Show all albums) Howdy Folks! Going to give this another try as my first attempt didn't go so well on the 'Diner-conversion' thread (Will update/edit that soon). Started my Cummins swap by pulling off the bumper; only took better part of an hour. That sucker is HEAVY! Better part of a 100 lbs I bet. Will be looking to knock substantial weight off that baby while still retaining a 5000 lb towing standard. This will take a while as it will unfold as time and resources permit, so please be patient. More pics and hopefully some videos (FMC-TV) to follow. Cheers, Terry #846

Show Newest Photos First | Show Oldest Photos First 238 Photos - Page : [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20]
New seals and yoke nuts done, now torque the yoke-nuts back and get this sucker back home where she belongs. Note on the pinion nut torque: After a lengthy discussion with Gord, at WestCoast Gear in Vancouver BC., I took his advise and nearly halved the previous torque spec (from 600 ft/lbs down to 350 ft/lbs) on the pinion yoke nut. He's rebuilt hundreds of gear cases for all kinds of heavy equipment and he was positive that 600 ft/lbs was far more than necessary. Again, this only his opinion and I happen to agree. What you chose to do is your business.	Took a bit of looking but I found a cheap pulley wheel for an electric motor etc. that fit perfect to gently drift/tap the new oil seal into place. Be careful not to let it get tilted out of whack.		Once you pull the pinion assembly out (carefully so as not to damage or mix up the shims) you'll need to separate the front flange to get at the pinion oil seal. Do this by threading 3 bolts into the holes provided and turn them in slowly equal in turns as best you can to part the flange. When you're done, clean the parts of old gasket/seal material and use a good quality RTV sealant to make a new gasket as they are no longer available. I found a cheap pulley wheel to use as a punch to drift the new seal into place. Worked perfectly.
Oil seals: 2 x #A1205L766 1 x #A1205K635 Pinion & Output yoke nuts: 1 x Pinion nut - #1227C939 2 x Prop shaft nut - #1227Z936	6-new U-joints from MP Parts in SC.	In the end, I had to make a couple of additional notches over the two nuts closest to the bedbase wall. Drilled a jigsaw pilot-hole from above where I anticipated each of the nuts were, then with a metal blade jigsaw, cut out all four corners.(Note: there's hoses and shit under the floor so be certain of blade clearances BEFORE you cut) This will be a real easy floor fix when I'm done, and the procedure saved me huge time and effort.
	(1 Comments) Took measurements from underneath using the forward end of the fiberglass trans tunnel (end of tape butted against it) to figure where to cut the floor. If you do this, use a skilsaw with the blade depth at about 5/8" as the sheetmetal is directly beneath it.	My friend and project supervisor, Liam. He's a Cummins-nut same as me and is also shop-foreman at a large Chrysler dealership in town. Helps keep me and my 'ideas' grounded in the real world.	This lift was invaluable to enable me to do this on my own. I'm on roadbase/gravel so an 8ft strip of 3/4" plywood made the perfect runway under the coach to get it out then back in again.
Show Newest Photos First | Show Oldest Photos First 238 Photos - Page : [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20]

Return to viewing all photo albums

	Running MegaBBS ASP Forum Software © 2002-2025 PD9 Software	(Delete all cookies set by this site)